silicon and hexafluorosilicate

The growing field of silicon solar cells requires a substantial reduction in the cost of semiconductor grade silicon, which has been mainly produced by the rod-based Siemens method. Because silicon can react with almost all of the elements and form a number of alloys at high temperatures, it is highly desired to obtain high purity crystalline silicon at relatively low temperatures through low cost process. Here we report a fast, complete and inexpensive reduction method for converting sodium hexafluorosilicate into silicon at a relatively low reaction temperature (∼ 200 °C). This temperature could be further decreased to less than 180 °C in combination with an electrochemical approach. The residue sodium fluoride is dissolved away by pure water and hydrochloric acid solution in later purifying processes below 15 °C. High purity silicon in particle form can be obtained. The relative simplicity of this method might lead to a low cost process in producing high purity silicon.

Topics: Catalysis; Crystallization; Fluorides; Nanotechnology; Silicic Acid; Silicon; Sodium; Temperature

Ammonium hexafluorosilicate (AHF) has been applied to arrest caries without discoloration. The purpose of this study was to observe structural and elemental changes of demineralized and AHF applied primary tooth enamel. Enamel from the labial surface of 20 primary canines was divided into an unground side and ground side at the center of the tooth, and demineralized with 35% phosphoric acid for 6 min. The teeth were divided into 4 groups according to a 3-min application of AHF and 1 week of soaking in artificial saliva, as follows: group A (neither AHF nor saliva), group B (only saliva), group C (only AHF), and group D (AHF and saliva), and then subdivided according to whether the enamel was ground or unground. Specimens were analyzed with scanning electron microscopy (SEM) and energy dispersive X-ray spectrometry (EDS). The data were statistically analyzed using ANOVA and Fisher's PLSD test at α = 0.05. In groups A and B, prism structures were seen, however, in groups C and D, enamel surfaces were covered with spherical particles. Ca/P ratio was significantly higher in groups C and D than in groups A and B. There was no significant difference between ground and unground enamel in the content of any element. The values for F, Na, Mg and Si persents and Ca/P ratio were significantly higher for the enamel surface than for points 10-30 µm beneath the surface. Results of this study suggest the possibility that AHF treatment arrests caries, although further study will be required to confirm this result.

Topics: Calcium; Cariogenic Agents; Cariostatic Agents; Cuspid; Dental Enamel; Fluorides; Humans; Magnesium; Microscopy, Electron, Scanning; Phosphoric Acids; Phosphorus; Saliva, Artificial; Silicic Acid; Silicon; Sodium; Spectrometry, X-Ray Emission; Tooth Demineralization; Tooth Remineralization; Tooth, Deciduous

A procedure for the automated determination of isotopic abundances of silicon from biogenic and lithogenic particulate matter and from dissolved silicon in fresh or saltwaters is reported. Samples are purified using proven procedures through the reaction of Si with acidified ammonium molybdate, followed by precipitation with triethylamine and combustion of the precipitate to yield silicon dioxide. The silicon dioxide is converted to cesium hexafluosilicate by dissolution in hydrogen fluoride and the addition of cesium chloride. Isotopic analysis is accomplished by decomposing the cesium hexafluosilicate with concentrated sulfuric acid to generate silicon tetrafluoride gas. Silicon tetrafluoride is purified cryogenically and analyzed on a gas source isotope ratio mass spectrometer. Yields of silicon tetrafluoride are >99.5%. The procedure can be automated by modifying commercial inlet systems designed for carbonate analysis. The procedure is free of memory effects and isotopic biases. Reproducibility is +/-0.03-0.10 per thousand for a variety of natural and synthetic materials.

Topics: Acids; Fluorides; Fluorine; Isotopes; Mass Spectrometry; Silicic Acid; Silicon

Previous studies on the surface properties of Dicor castable glass-ceramic have shown the formation of a specific crystalline phase at the glass-ceramic/embedment interface. If this phase is not removed by grinding, it leads to an undesirable strength decrease. The aims of this study were: (1) to determine the nature of this surface layer, (2) to promote the formation of a different crystalline phase at the surface with the intention of improving the properties of the glass-ceramic, by modification of the composition of the Dicor ceramming embedment, and (3) to evaluate the fracture toughness and flexural strength of Dicor glass-ceramic after embedment modification. Modifications were made to the embedment by incorporation of 2.5 wt% of lithium fluoride and ceramming at various temperatures. X-ray diffraction was used to determine the crystalline nature of the surface layer. Fracture toughness was investigated by the indentation technique. The maximum bi-axial stresses were calculated after the samples were fractured in water on a ball-on-ring fixture at 0.5 mm/min. With the recommended embedment and ceramming cycle, the crystalline phase constituting the ceram layer was a calcium magnesium silicate CaMg(SiO3)2 (diopside). The crystalline composition of the ceram layer was successfully modified by addition of 2.5 wt% lithium fluoride to the embedment. This promoted the crystallization of mica in the ceram layer and increased the fracture toughness of the glass-ceramic when the ceramming temperature was 950 or 975 degrees C. The flexural strength was significantly increased when the ceramming temperature was 1000 degrees C.

Topics: Aluminum; Aluminum Compounds; Calcium; Ceramics; Crystallography; Dental Porcelain; Elasticity; Electron Probe Microanalysis; Fluorides; Glass; Hardness; Lithium; Lithium Compounds; Magnesium; Magnesium Silicates; Materials Testing; Potassium; Silicic Acid; Silicon; Stress, Mechanical; Surface Properties; X-Ray Diffraction; Zirconium

Topics: Fluorides; Poisons; Silicic Acid; Silicon; Sodium

Topics: Animals; Fluorides; Silicic Acid; Silicon; Sodium; Swine; Swine Diseases; Trichinellosis

Topics: Fluorides; Fluorine; Humans; Occupational Diseases; Silicic Acid; Silicon; Sodium; Sodium, Dietary