silicon and fluorapatite

To evaluate the microhardness and surface elemental compositions of ceramics immersed in acidic agents.. Thirty-five ceramic disc specimens were made from each of four types of ceramic (VMK 95, Vitadur Alpha, Empress Esthetic and IPS e.max Ceram). Before immersion, baseline data of Vicker's microhardness and elemental composition were recorded. Four groups of discs (seven per group) were then immersed in acidic agents (citrate buffer solution, pineapple juice and green mango juice) and deionized water (as a control) for 168 h at 37 degrees C. One group was immersed in 4% acetic acid at 80 degrees C for 168 h. After immersion, specimens were evaluated and data were analyzed using two-way ANOVA with repeated measurements and a paired t-test at a significance level of 0.05.. The microhardness values of four types of ceramic significantly decreased after being immersed in acidic agents (p < 0.05). The elemental compositions of ceramics mainly comprise silicon, aluminium and potassium. These compositions also decreased after immersion (p < 0.05).. The acidic agents used in this study affected the microhardness and elemental dissolution of ceramics. The main elemental compositions of ceramics (silicon, aluminium and potassium) decreased after being immersed in acidic agents.

Topics: Acetic Acid; Acids; Aluminum; Aluminum Oxide; Aluminum Silicates; Ananas; Apatites; Beverages; Buffers; Citric Acid; Dental Porcelain; Hardness; Humans; Hydrogen-Ion Concentration; Immersion; Mangifera; Materials Testing; Potassium; Potassium Compounds; Silicon; Solubility; Spectrometry, X-Ray Emission; Surface Properties; Temperature; Time Factors; Water

In bone tissue engineering, ionic doping using bone-related minerals such as magnesium (Mg) or strontium (Sr) is a promising strategy to make up for the inherent disadvantages (low solubility) of various apatite-based materials (such as fluorapatite (FAp) and hydroxyapatite (HA)). Therefore, some studies in recent years have tried to address the lack-of-methodology to improve the properties of bioceramics in the field. Even though the outcome of the studies has shown some promises, the influence of doped elements on the structures and properties of in-vitro and in-vivo mineralized FAp has not been investigated in detail so far. Thus, it is still an open question mark in the field. In this work, strontium modified fluorapatite (Sr-FAp), magnesium and silicon modified fluorapatite (Mg-SiFAp) bioceramics were synthesized using a mechanical alloying methodology. Results showed that the doped elements could decrease the crystallinity of FAp (56%) to less than 45% and 39% for Sr-FAp and Mg-SiFAp, respectively. Moreover, in-vitro studies revealed that Sr-FAp significantly enhanced osteogenic differentiation of hMSCs, after 21 days of culture, compared to Mg-SiFAp at both osteogenic and normal media. Then, in vivo bone formation in a defect of rat femur filled with a Sr-FAp and Mg-SiFAp compared to empty defect was investigated. Histological analysis revealed an increase in bone formation three weeks after implanting Sr-FAp compared to Mg-SiFAp and the empty defect. These results suggest that compared to magnesium and silicon, strontium ion significantly promotes bone formation in fluorapatite, making it appropriate for filling bone defects.

Topics: Animals; Apatites; Ions; Magnesium; Osteogenesis; Rats; Silicon; Strontium

The aim of this study was to fabricate and characterize biodegradable polycaprolactone fumarate(PCLF)/gelatin-based nanocomposite incorporated with the 0, 5 and 10 wt% silicon and magnesium co-doped fluorapatite nanoparticles (Si-Mg-FA) membranes using electrospinning process for guided bone regeneration (GBR) and guided tissue regeneration (GTR) applications. Results demonstrated the formation of randomly-oriented and defect-free fibers with various fiber sizes depending on the Si-Mg-FA content. Moreover, incorporation of 5 wt% Si-Mg-FA significantly improved the mechanical strength (1.5times) compared to the mechanical strength of PCLF/gelatin membrane and nanocomposite with 10 wt% nanoparticles. There was no clear difference between degradation rate of PCLF/gelatin and PCLF/gelatin with 5 wt% nanoparticles at 7, 14 and 28 days of immersion in phosphate buffer saline while 10 wt% nanoparticles significantly increased biodegradation of PCLF/gelatin, and no cytotoxic effect of membranes was seen. Finally, scanning electron microscopy (SEM) micrographs of fibroblast cells cultured on the samples demonstrated that the cells were completely attached and spread on the surface of nanocomposites. In summary, PCLF/gelatin membranes consisting of 5 wt% Si-Mg-FA nanoparticles could provide appropriate mechanical and biological properties and fairly good degradation rate, making it appropriate for GTR/GBR applications.

Topics: Apatites; Gelatin; Magnesium; Nanocomposites; Nanoparticles; Polyesters; Silicon

To investigate the effect of surface polishing and finishing methods on the surface roughness of restorative ceramics.. Disk specimens were prepared from feldspar-based, lithium disilicate-based, fluorapatite leucite-based and zirconia ceramics. Four kinds of surface polishing/finishing methods evaluated were: Group 1:. carborundum points (CP); Group 2: silicon points (SP); Group 3: diamond paste (DP); Group 4: glazing (GZ). Surface roughness was measured using an interferometer and the parameters of Sa (average height deviation of the surface) and St (maximum peak-to-valley height of the surface) were evaluated. Data were statistically analyzed using two-way ANOVA (P < 0.05) followed by post-hoc test. The mean values were also compared by Student's t-test. Specimen surfaces were evaluated by 3-D images using an interferometer.. The zirconia showed the least surface roughness (Sa and St) values after grinding with carborundum points. The significantly lowest Sa values and St values were obtained for lithium disilicate and zirconia ceramics surfaces finished with DP and GZ. The fluorapatite leucite ceramic showed significantly reduced Sa and St values from DP to GZ. The feldspathic porcelain showed the highest surface roughness values among all types of ceramics after all of the polishing/finishing procedures.

Topics: Aluminum Silicates; Apatites; Carbon Compounds, Inorganic; Ceramics; Dental Materials; Dental Polishing; Dental Porcelain; Diamond; Humans; Interferometry; Materials Testing; Potassium Compounds; Silicon; Surface Properties; Zirconium

This study was conducted to evaluate the titratable acidity and effect of naturally acidic agents on the surface microhardness, elemental composition, and surface morphology of fluorapatite-leucite ceramics. One hundred and ten ceramic disks (IPS d.SIGN), 12.0 mm in diameter and 2.0 mm in thickness, were fabricated. Before immersion, the baseline data of Vickers microhardness and elemental composition were recorded. Four groups were immersed in acidic agents (citrate buffer solution, green mango juice, and pineapple juice) and deionized water (control) at 37ºC for 168 hours, whereas one group was immersed in 4% acetic acid at 80ºC for 168 hours. After immersion, specimens were evaluated and data were analyzed using one-way repeated ANOVA and Tukey's test (α=0.05). Microhardness values significantly decreased after immersion (p<0.05). In terms of elemental composition, the weight percentages of silicon, potassium, aluminum, and sodium also decreased after immersion (p<0.05). Results of this study showed that fluorapatite-leucite ceramics were affected by long-term immersion in acidic agents.

Topics: Acetic Acid; Acids; Aluminum; Aluminum Silicates; Ananas; Apatites; Beverages; Chemical Phenomena; Citric Acid; Dental Porcelain; Hardness; Humans; Hydrogen-Ion Concentration; Mangifera; Materials Testing; Potassium; Silicon; Sodium; Surface Properties; Temperature; Time Factors; Water

The proteins lysozyme, amylase, and bovine serum albumin (BSA) were adsorbed on two experimental dental materials, made of fluoroapatite particles embedded in polymer matrices, and on silicon wafers. The protein films were prepared as single-component layers, as binary mixtures, and as double layers. These systems were investigated by time-of-flight secondary ion mass spectrometry (ToF-SIMS) and the multivariate data analysis technique of discriminant principal-component analysis (DPCA). During adsorption of a single protein film on to the solid surfaces, the three proteins could be clearly distinguished by the scores of their mass spectra after selection of amino acid-related peaks and DPCA. Furthermore, very similar results were obtained on the two different fluoroapatite substrates. For samples coated with binary layers of two proteins adsorbed simultaneously, it was found for both substrate types that BSA shows the strongest ability to adsorb followed by lysozyme, while amylase has the smallest ability. By contrast, the consecutive adsorption of two protein layers showed a strong influence of substrate type on the adsorption ability of the proteins.

Topics: Adsorption; Amylases; Animals; Apatites; Cattle; Dental Materials; Discriminant Analysis; Humans; Multivariate Analysis; Muramidase; Serum Albumin, Bovine; Silicon; Spectrometry, Mass, Secondary Ion