muramidase and polygalacturonic-acid

A quartz crystal microbalance with dissipation monitoring (QCMD) has been used to monitor the adsorption and structure of lysozyme monolayers and multilayers, and poly-L-lysine (PLL)-polygalacturonic acid (PGalA) multilayers at a solid-liquid interface using freshly-cleaved mica as a substrate. QCMD measurements were complemented with atomic force microscopy (AFM). AFM images revealed that lysozyme formed incomplete monolayers and provided a basis for calculation of the thickness of the protein film. Comparative studies of adsorption onto standard and mica-coated quartz crystals showed higher areal mass adsorption and a longer-time adsorption process for mica-coated quartz crystals. Simultaneous AFM images and QCMD data were obtained for lysozyme, linear PLL-PGalA and 7 nm PLL dendrimer-PGalA multilayers. The layer-by-layer deposited multilayer films exhibited viscoelastic properties and their growth followed a non-linear regime, associated with the PLL diffusion in and out of the film formation for linear PLL-PGalA films. For the PLL 7 nm dendrimer-PGalA films the AFM images revealed marked changes in surface roughness during layer by layer deposition: these changes influence the interpretation of the QCMD data and provide additional information on the growth and structure of the multilayers.

Topics: Animals; Chickens; Microscopy, Atomic Force; Muramidase; Pectins; Polylysine; Quartz Crystal Microbalance Techniques

The effect of pH on the stability of layer-by-layer deposited polygalacturonic acid (PGalA)-based multilayer films prepared with the polycations poly-L-lysine, chitosan, and lysozyme is studied. The response was characterized using a quartz crystal microbalance, dual polarization interferometry, and Fourier transform infrared spectroscopy which probe multilayer thickness, density, polymer mass (composition and speciation), and hydration. All multilayers showed irreversible changes in response to pH change becoming thinner due to the partial disassembly. Preferential loss of the polycation (50-80% w/w) and relative small losses of PGaLA (10-35% w/w) occurred. The charge density on the polycation has a strong influence on the response to the acid cycle. Most of the disassembly takes place at the pH lower that pK(a) of PGaLA, indicating that this factor was crucial in determining the stability of the films. The pH challenge also revealed a polycation-dependent shift to acid pH in the PGaLA pK(a).

Topics: Chitosan; Hydrogen-Ion Concentration; Membranes, Artificial; Muramidase; Pectins; Polylysine

A novel immobilisation design for increasing the final concentration of the heterologous protein lysozyme by a genetically engineered fungus, Aspergillus niger B1, was developed. A central composition design was used to investigate different immobilised polymer types (alginate and pectate), polymer concentration [24% and 4% (w/v)], inoculum support ratios (1:2 and 1:4) and gel-inducing agent concentration [CaCl(2), 2% and 3.5% (w/v)]. Studies of the kinetics of production showed that optimum lysozyme productivity occurred after 10 days. Lysozyme production was significantly affected by polymer type, polymer concentration, and inoculum support ratio. Overall, immobilisation in Ca-pectate resulted in higher lysozyme production compared to that in Ca-alginate. Similar effects were observed when the polymer concentration was reduced. Regardless of polymer type and concentration, increasing the fungal inoculum level increased lysozyme production. A significantly higher lysozyme yield was achieved with Ca-pectate in comparison to Ca-alginate (approximately 20-23 mg l(-1) and 0.5-2 mg l(-1), respectively). The maximum lysozyme yield achieved was about 23 mg l(-1) by immobilisation in Ca-pectate 2% (w/v) with 33% (v/v) mycelium and 3.5% (w/v) gel-inducing agent (CaCl(2)). Response surface methodology was used to investigate the effect of pH and water activity (a(w)). The best medium pH was 4.5-5.0, and bead a(w) for optimum lysozyme yield was 0.94, regardless of polymer type.

Topics: Alginates; Aspergillus niger; Bioreactors; Calcium Chloride; Cloning, Molecular; Culture Media; Fermentation; Glucuronic Acid; Hexuronic Acids; Hydrogen-Ion Concentration; Muramidase; Pectins