fumarates and hydroxyethyl-methacrylate

A new total biomimetic technique based on both the water uptake and degradation processes is introduced in this study to provide an interesting procedure to fabricate a bioactive and biodegradable synthetic scaffold, which has a good mechanical and structural properties. The optimization of effective parameters to scaffold fabrication was done by response surface methodology/central composite design (CCD). With this method, a synthetic scaffold was fabricated which has a uniform and open-interconnected porous structure with the largest pore size of 100-200μm. The obtained compressive ultimate strength of ~35MPa and compression modulus of 58MPa are similar to some of the trabecular bone. The pore morphology, size, and distribution of the scaffold were characterized using a scanning electron microscope and mercury porosimeter. Fourier transform infrared spectroscopy, EDAX and X-ray diffraction analyses were used to determine the chemical composition, Ca/P element ratio of mineralized microparticles, and the crystal structure of the scaffolds, respectively. The optimum biodegradable synthetic scaffold based on its raw materials of polypropylene fumarate, hydroxyethyl methacrylate and nano bioactive glass (PPF/HEMA/nanoBG) as 70/30wt/wt%, 20wt%, and 1.5wt/wt% (PHB.732/1.5) with desired porosity, pore size, and geometry were created by 4weeks immersion in SBF. This scaffold showed considerable biocompatibility in the ranging from 86 to 101% for the indirect and direct contact tests and good osteoblast cell attachment when studied with the bone-like cells.

Topics: Biocompatible Materials; Biomimetics; Bone Substitutes; Cell Line; Cell Survival; Compressive Strength; Fumarates; Glass; Humans; Methacrylates; Microscopy, Electron, Scanning; Nanocomposites; Polypropylenes; Porosity; Prohibitins; Research Design; Spectrometry, X-Ray Emission; Spectroscopy, Fourier Transform Infrared; Tissue Scaffolds; X-Ray Diffraction

Biodegradable bone plates were prepared as semi-interpenetrating networks (SIPN) of crosslinked polypropylene fumarate (PPF) within a host matrix of either poly(lactide-co-glycolide)-85:15 (PLGA) or poly(1-lactide-co-d,l-lactide)-70:30 (PLA) using N-vinylpyrrolidone (NVP), ethylene glycol dimethacrylate (EGDMA), 2-hydroxyethyl methacrylate (HEMA), and methyl methacrylate (MMA) as crosslinking agents. Hydroxyapatite (HAP), an inorganic filler material, was used to further augment mechanical strength. The control crosslinking agent (NVP) was replaced partially and totally with other crosslinking agents. The amount of crosslinking agent lost, the characterization change in the mechanical properties and the dimensional stability of the bone plates after in vitro treatment was calculated. The optimum crosslinking agent was selected on the basis of low in vitro release of NVP from SIPN matrix. Bone plates were then prepared using this crosslinking agent at 5 MPa pressure and at temperatures between 100-140 degrees C to determine if there was any augmentation of mechanical properties in the presence of the crosslinked network. In vitro analysis showed that 90% of the crosslinking agent was lost on plates using NVP as a crosslinking agent. This loss was reduced to 50% when NVP was partially replaced with EGDMA or MMA. EGDMA was determined to be superior because (1) its low release as a crosslinking agent, (2) flexural plate strength of 50-67 MPa, (3) flexural modulus of 7-13 GPa, and (4) manufacturability stiffness of 300-600 N/m. HAP-loading resulted in an additional increase in values of mechanical parameters. Substituting PLGA with PLA in the PPF-SIPN did not show any additional improvement of mechanical properties.

Topics: Absorbable Implants; Biocompatible Materials; Bone Plates; Cross-Linking Reagents; Durapatite; Elasticity; Equipment Design; Fumarates; Hot Temperature; Humans; Lactic Acid; Methacrylates; Methylmethacrylate; Pliability; Polyesters; Polyglycolic Acid; Polylactic Acid-Polyglycolic Acid Copolymer; Polymers; Polypropylenes; Pressure; Pyrrolidinones; Stress, Mechanical