ethyl-cellulose and hydroxypropylmethylcellulose-acetate-succinate

Topics: Animals; Cellulose; Dosage Forms; Excipients; Gastrointestinal Tract; Male; Methylcellulose; Particle Size; Pharmaceutical Preparations; Pilot Projects; Polymers; Polyvinyls; Positron Emission Tomography Computed Tomography; Printing, Three-Dimensional; Rats; Rats, Sprague-Dawley; Rodentia; Technology, Pharmaceutical

Dry powder coating is a technique to coat substrates without the use of organic solvent or water. The polymer powder is directly applied to the cores to be coated. Liquid additives are often used to lower the glass transition temperature of the polymer and to enhance the adhesion of the powder to the cores. This leads to an increase in coating efficiency of the process. The impact of various liquid additives and their properties like spreading behavior, viscosity and plasticizing activity were investigated with respect to their influence on the coating efficiency of the process. Ethylcellulose and hydroxypropyl methylcellulose acetate succinate were used as coating polymers. Spreading behavior of the liquid additive on the polymer was the most influencing parameter and could be successfully predicted with contact angle measurements on polymer films. Calculations of works of adhesion and spreading coefficients also revealed to be promising predictive techniques for choosing suitable additives to improve process efficiency. Isopropyl myristate showed the best spreading behavior resulting in the highest coating efficiency. Based on these results, a formulation for ethylcellulose containing isopropyl myristate was developed and film formation was examined using dissolution testing and imaging techniques to evaluate the optimum curing conditions.

Topics: Cellulose; Drug Compounding; Excipients; Methylcellulose; Polymers; Powders; Pressure; Solubility; Surface Tension; Transition Temperature; Viscosity

Blends of aqueous dispersions of a water-insoluble and an enteric polymer, namely ethyl cellulose:hydroxypropyl methylcellulose acetate succinate (EC:HPMCAS) and ethyl cellulose:methacrylic acid ethyl acrylate copolymer (EC:Eudragit L), were used as coating materials to control theophylline release from matrix pellets. Varying the polymer blend ratio, broad ranges of drug release patterns were obtained at low as well as at high pH. Interestingly, the resulting release profiles were rather similar for both types of blends in 0.1 M HCl, whereas significant differences were observed in phosphate buffer pH 7.4. Surprisingly, drug release at high pH was much slower for EC:HPMCAS blends compared to EC:Eudragit L blends, although HPMCAS leached out more rapidly (and to a higher extent) from the film coatings than Eudragit L. To explain these phenomena and to better understand the underlying drug release mechanisms, thin polymeric films of identical composition as the pellet coatings were prepared and physicochemically characterized before and upon exposure to the release media. Importantly, the polymer particle size was identified to be a very crucial formulation parameter, determining the resulting film coating structure and properties. The Eudragit L particles are much smaller than the HPMCAS particles (nano- vs. micrometer size range) and, thus, more effectively hinder the formation of a continuous and mechanically stable EC network. Consequently, the EC structures remaining after enteric polymer leaching at high pH are mechanically much weaker in the case of Eudragit L. Upon exposure to phosphate buffer, water-filled cracks are formed, through which the drug rapidly diffuses out. In contrast, the EC structures remaining upon HPMCAS leaching are mechanically stronger and drug release is controlled by diffusion through the polymeric remnants.

Topics: Cellulose; Chemical Phenomena; Chemistry, Physical; Chromatography, High Pressure Liquid; Dosage Forms; Drug Carriers; Drug Stability; Emulsions; Hardness Tests; Kinetics; Methylcellulose; Microscopy, Electron, Scanning; Particle Size; Plasticizers; Polymers; Polymethacrylic Acids; Surface Properties; Theophylline

The purpose of this study was to develop a new method for preparing controlled release (CR) matrix pellets by annealing with water-insoluble polymers, and to elucidate a relationship between the annealing temperature of the matrix pellets and a glass transition temperature (T(g)) or a minimum film-forming temperature (MFT) of the polymer/plasticizer systems that constituted the matrix pellets. The pellets containing theophylline as a model drug were prepared by the extrusion-spheronization method and subsequent annealing. The pellets were characterized mainly by pellet formation, release studies, and thermal evaluations. It was apparent that the annealing temperature for the CR matrix pellets was related to the T(g) and MFT of the polymer/plasticizer systems. For ethylcellulose (EC) containing 22.7% triethylcitrate (TEC), the annealing temperature required for preparing CR pellets was 80 degrees C, which was more than 20 degrees C higher than the T(g) and MFT of this EC/TEC system. In contrast, hydroxypropylmethylcellulose acetate succinate (HPMCAS) containing 22.7% TEC could be used to prepare CR pellets without heating. The T(g) of this HPMCAS/TEC system was about 60 degrees C and the MFT was lower than 20 degrees C, indicating that water can act as a plasticizer for HPMCAS and that HPMCAS/TEC pellets could be annealed at room temperature. These results suggest that MFT is a better indicator than T(g) for estimating annealing temperature. SEM observation showed that the EC/TEC pellets annealed at 80 degrees C had a matrix structure with coalesced particles. On the contrary, unannealed pellets consisted of individually distinguishable particles. The release rate of drug from the matrix CR pellets was dependent on the drug concentration and polymer to plasticizer ratio.

Topics: Cellulose; Drug Compounding; Drug Implants; Drug Stability; Excipients; Hardness; Methylcellulose; Microscopy, Electron, Scanning; Particle Size; Polymers; Solubility; Temperature; Theophylline; Water; X-Ray Diffraction

A new method for preparation of large amounts of empty pressure-controlled colon delivery capsules (PCDCs) by a dipping method has been developed. Empty PCDCs are composed of two polymer membranes. The inner one was a water-insoluble polymer membrane, ethylcellulose (EC). The outer one was an enteric polymer membrane, hydroxypropylmethylcellulose phthalate (HPMCP) or hydroxypropylmethylcellulose acetate succinate (HPMCAS). By consequently dipping into an ethanolic EC solution and an alkalized enteric polymer solution, empty PCDCs were obtained after both the capsule body and cap were adjusted to the size of #2 capsules. With each enteric polymer, two types of empty PCDCs of different thickness were prepared. Fluorescein (FL) was formulated with suppository base, PEG1000, and used as a model drug. FL/PEG1000 suspension was introduced into empty PCDCs which were then sealed with enteric polymer solution. The PCDCs were evaluated by an in vivo experiment using beagle dogs. After oral administration of the test PCDC preparations containing 30 mg of FL, blood samples were obtained from the jugular vein and serum FL levels were measured. The thickness of the EC membrane layer varied in both the capsule body and cap. HPMCAS PCDCs had 62.1+/-5.0 (S.E.) microm (body) and 49.7+/-3.3 microm (cap) with thicker ones and 55.7+/-6.6 microm (body) and 46.8+/-6.2 microm (cap) with thinner ones. HPMCP PCDCs had 28.1+/-3.3 microm (body), 30.9+/-1.0 microm (cap) with thinner ones and 43.1+/-9.8 microm (body), 42.4+/-8.2 microm (cap) with thicker ones. The mean T(i) values, the first appearance time, of FL in the serum of HPMCAS PCDCs were 2.0+/-0.7 h for thicker ones and 3.8+/-0.5 h for thinner ones, while the mean T(i) values of HPMCP PCDCs were 2.0+/-0.0 h for thinner ones and 3.5+/-0.7 h for thicker ones. Since the colon arrival time in beagle dogs was 3.5+/-0.3 h as determined by a sulfasalazine test, thinner HPMCAS PCDCs and thicker HPMCP PCDCs were thought to deliver FL to the colon.

Topics: Animals; Area Under Curve; Capsules; Cellulose; Colon; Contrast Media; Dogs; Drug Delivery Systems; Excipients; Fluorescein; Male; Methylcellulose; Sclerosing Solutions

A spray method for the preparation of free films from aqueous polymeric dispersions was investigated. Free films were prepared from aqueous dispersions of methacrylic acid-ethyl methacrylate copolymer (Eudragit L 30D), hydroxypropyl methylcellulose acetate succinate (HPMCAS), cellulose acetate phthalate (CAP), and ethyl cellulose (EC) by a spray method and a cast method, and their mechanical properties and reproducibility were investigated. Uniform films were obtained from the dispersions of Eudragit L 30D, HPMCAS, and EC by the spray method, but films could not be formed by spraying the CAP dispersion. The tensile strength, elongation, and elastic modulus of the sprayed Eudragit L 30D films were similar to the properties of the cast films, and good reproducibility was obtained from both methods. Marked within-run variation in the mechanical properties was observed for the cast HPMCAS and CAP films, which could be due to a settling of the solid particles during the drying step. The variation in the mechanical properties of the sprayed HPMCAS films was lower and the tensile strength significantly higher than that of the cast films. There were also significant differences in tensile strength and elongation of EC films between products of the two methods. The results indicated that the spray method used to prepare the free films from aqueous polymeric dispersions provided uniform films with consistent and reproducible properties.

Topics: Acrylic Resins; Cellulose; Chemistry, Pharmaceutical; Delayed-Action Preparations; Dosage Forms; Gels; Methylcellulose; Polymers; Polymethacrylic Acids; Reproducibility of Results; Surface Properties; Water

Hydroxy propyl methyl cellulose acetate succinate high grade (AS-HG) and ethyl cellulose (EC) mixture microcapsules containing cefadroxil or theophylline were prepared by a solvent evaporation method in liquid paraffin dissolved sorbitan tri-stearate as a dispersing agent, and their sustained-release properties were evaluated. The microcapsules prepared with AS-HG:EC (in a 2:5 weight ratio) mixture containing 20% of cefadroxil or theophylline exhibited apparent zero-order releasing pattern in pH 6 to 8, at 50 rpm and 37 degrees C (paddle method). These microcapsules were administered orally to beagle dogs and the plasma concentrations of cefadroxil or theophylline were measured periodically. As a result of in vivo investigation, a satisfactory sustained-release plasma pattern and an apparent zero-order process in the gastrointestinal absorption were confirmed by deconvolution analysis of both drugs.

Topics: Administration, Oral; Animals; Cefadroxil; Cellulose; Delayed-Action Preparations; Dogs; Drug Compounding; Intestinal Absorption; Male; Methylcellulose; Theophylline