cytochrome-c-t and glycidyl-methacrylate

Since sequential injection chromatography (SIC) emerged in 2003, it has been used for separation of small molecules in diverse samples, but separations of high molar mass compounds such as proteins have not yet been described. In the present work a poly(glycidyl methacrylate-co-ethylene dimethacrylate) (GMA-co-EDMA) monolithic column was prepared by free radical polymerization inside a 2.1-mm-i.d. activated fused silica-lined stainless steel tubing and modified with iminodiacetic acid (IDA). The column was prepared from a mixture of 24% GMA, 16% EDMA, 20% cyclohexanol, and 40% 1-dodecanol (all% as w/w) containing 1% of azobisisobutyronitrile (AIBN) (in relation to monomers). Polymerization was done at 60 °C for 24 h. The polymer was modified with 1.0 M IDA (in 2 M Na2CO3, pH 10.5) at 80 °C for 16 h. Separation of myoglobin, ribonuclease A, cytochrome C, and lysozyme was achieved at pH 7.0 (20 mM KH2PO4/K2HPO4) using a salt gradient (NaCl). Myoglobin was not retained, and the other proteins were separated by a gradient of NaCl created inside the holding coil (4 m of 0.8-mm-i.d. PTFE tubing) by sequential aspiration of 750 and 700 μL of 0.2 and 0.1 M NaCl, respectively. As the flow was reversed toward the column (5 μL s(-1)) the interdispersion of these solutions created a reproducible gradient which separated the proteins in 10 min, with the following order of retention: ribonuclease A < cytochrome C < lysozyme. The elution order was consistent with a cation-exchange mechanism as the retention increased with the isoelectric points.

Topics: Animals; Cattle; Chickens; Chromatography, Ion Exchange; Cytochromes c; Epoxy Compounds; Horses; Methacrylates; Muramidase; Myoglobin; Polymers; Ribonuclease, Pancreatic

A monolithic enzymatic microreactor was prepared in a fused-silica capillary by in situ polymerization of acrylamide, glycidyl methacrylate (GMA) and ethylene dimethacrylate (EDMA) in the presence of a binary porogenic mixture of dodecanol and cyclohexanol, followed by ammonia solution treatment, glutaraldehyde activation and trypsin modification. The choice of acrylamide as co-monomer was found useful to improve the efficiency of trypsin modification, thus, to increase the enzyme activity. The optimized microreactor offered very low back pressure, enabling the fast digestion of proteins flowing through the reactor. The performance of the monolithic microreactor was demonstrated with the digestion of cytochrome c at high flow rate. The digests were then characterized by CE and HPLC-MS/MS with the sequence coverage of 57.7%. The digestion efficiency was found over 230 times as high as that of the conventional method. In addition, for the first time, protein digestion carried out in a mixture of water and ACN was compared with the conventional aqueous reaction using MS/MS detection, and the former solution was found more compatible and more efficient for protein digestion.

Topics: Animals; Cattle; Chromatography, Liquid; Cytochromes c; Enzymes, Immobilized; Epoxy Compounds; Heart; Horses; Methacrylates; Microchemistry; Peptide Fragments; Peptide Mapping; Spectrometry, Mass, Electrospray Ionization; Spectrometry, Mass, Matrix-Assisted Laser Desorption-Ionization; Trypsin

Topography and thickness of hydrophilic polymer coatings of fused-silica capillaries for capillary electrophoresis (CE) were investigated using atomic force microscopy (AFM), scanning electron microscopy (SEM), and profilometry. Three hydrogels, poly(2-hydroxyethyl methacrylate) [poly(HEMA)], poly(diethylene glycol monomethacrylate) [poly(DEGMA)], and poly(triethylene glycol monomethacrylate) [poly(TEGMA)], were deposited using two procedures, either by simple physical sorption of the polymers, or by derivatization of the capillary wall surface with glycidyl methacrylate (EPMA) followed by polymerization of the appropriate monomers. The performance of the modified capillaries was tested under CE conditions (decrease in the electroosmotic flow, EOF dependence on pH, separation of milk and standard proteins). It has been found that the most important property of the polymer coating is its thickness, whereas its topography and the degree of its hydrophobicity are less significant. Film deposition by physical adsorption is preferable to polymerization on the derivatized surface.

Topics: Adsorption; Animals; Aprotinin; Carbonic Anhydrases; Cattle; Cytochromes c; Electrophoresis, Capillary; Epoxy Compounds; Imaging, Three-Dimensional; Membranes, Artificial; Methacrylates; Microscopy, Atomic Force; Microscopy, Electron, Scanning; Molecular Structure; Polyethylene Glycols; Polyhydroxyethyl Methacrylate; Polymethacrylic Acids; Sensitivity and Specificity; Serum Albumin, Bovine; Silicon Dioxide; Surface Properties; Time Factors