clay and phenyltrimethylammonium

The results presented in this paper show an impact of the concentration of the aromatic organic cation on the adsorption of acetochlor on the surface of the organic-modified montmorillonite. Natural montmorillonite from Bogovina (Boljevac municipality, Serbia) was used for organic modification in this experiment. Cation exchange capacity of this montmorillonite (86 mmol 100 g

Topics: Adsorption; Aluminum Silicates; Bentonite; Clay; Herbicides; Quaternary Ammonium Compounds; Serbia; Spectroscopy, Fourier Transform Infrared; Toluidines; X-Ray Diffraction

Bentonite clay was modified using quaternary ammonium cations, viz. phenyltrimethylammonium (PTMA), hexadecyltrimethylammonium (HDTMA), trioctylmethylammonium (TOMA) [100 % of cation exchange capacity of clay], and stearylkonium (SK) [100 % (SK-I) and 250 % (SK-II) of cation exchange capacity of clay]. The organoclays were characterized using X-ray diffraction (XRD), infrared (IR) spectroscopy, and scanning electron microscopy (SEM). Atrazine adsorption on modified clays was studied using a batch method. Bentonite clay was a poor adsorbent of atrazine as 9.4 % adsorption was observed at 1 μg mL(-1) atrazine concentration. Modification of clay by PTMA cation did not improve atrazine adsorption capacity. However, atrazine adsorption in HDTMA-, TOMA-, and SK-bentonites varied between 49 and 72.4 % and data fitted well to the Freundlich adsorption isotherm (R > 0.96). Adsorption of atrazine in organoclays was nonlinear and slope (1/n) values were <1. The product of Freundlich adsorption constants, K f(1/n) in HDTMA-, TOMA-, and SK-I-bentonites was 239.2, 302.4, and 256.6, respectively, while increasing the SK cation loading in the clay (SK-II) decreased atrazine adsorption [K f(1/n) - 196.4]. Desorption of atrazine from organoclays showed hysteresis and TOMA- and SK-I-bentonites were the best organoclays to retain the adsorbed atrazine. Organoclays showed better atrazine removal from wastewater than an aqueous solution. The synthesized organoclays may find application in soil and water decontamination and as a carrier for atrazine-controlled released formulations.

Topics: Adsorption; Aluminum Silicates; Atrazine; Bentonite; Cations; Clay; Quaternary Ammonium Compounds; Surface-Active Agents; Water; Water Pollutants, Chemical; X-Ray Diffraction

This study aimed to evaluate new methodology for designing ecologically acceptable formulations of acetochlor. Modification of montmorillonite with phenyltrimethylammonium chloride (PTMA) or benzyltrimethylammonium chloride (BTMA) and organoclay formulations of acetochlor were prepared in the presence of high concentrations of sodium chloride (150 g/L). Acetochlor concentration in the equilibrium solutions was determined by HPLC. Release of acetochlor in a water system was performed by a funnel experiment. Leaching of acetochlor in soil was determined by a bioassay using a column technique and Setaria viridis as a test plant. The adsorbed amounts of acetochlor on montmorillonite exchanged by PTMA or BTMA were increased as NaCl concentration increased in the equilibrium solution. Leaching of acetochlor from organoclay formulations was significantly inhibited to the top soil layer (0-5 cm) when the formulations were prepared at extreme NaCl concentration (100-150 g/L). These results are in accord with a funnel experiment that showed a reduction in acetochlor release from the montmorillonite-based formulations. The application of this method for herbicide formulation would produce ecologically acceptable herbicide formulations that can significantly minimize the risk to groundwater pollution.

Topics: Aluminum Silicates; Bentonite; Clay; Herbicides; Quaternary Ammonium Compounds; Sodium Chloride; Soil; Toluidines; Water Pollution, Chemical

A natural shale and four synthetic organoclays were compared as potential sorbent additives to containment barriers at hazardous waste sites. Trimethylphenyl ammonium bentonite (TMPA-bent) was shown in batch experiments to have the greatest sorption capacities for 1,2,4-trichlorobenzene, trichloroethylene, and methyl isobutyl ketone, followed by the shale and a commercial organoclay. Sorption capacities were lowest for hexadecyltrimethyl ammonium bentonite (HDTMA-bent) and hexadecyl pyridinium bentonite (HDP-bent). Operative sorption mechanisms for the organoclays depended on the size of the organic modifier, i.e., uptake by the TMPA-bent occurred via adsorption onto mineral surfaces, while that for the HDTMA-bent and HDP-bent took place by absorption into organic phases formed by their long hydrocarbon tails. The shale was found to be by far the most cost-effective sorbent, an important factor for large scale applications. Solids concentration effects (i.e., higher apparent sorption capacities at lower experimental sorbent concentrations) were exhibited by HDTMA-bent and HDP-bent. This can be attributed to aggregation of sorbent particles as a result of interactions among their hydrocarbon chains. Solids effects were observed to decline and eventually disappear as sorbent concentrations were increased. Such effects must be considered in applying batch sorption results to flow-through systems.

Topics: Adsorption; Aluminum Silicates; Clay; Cost-Benefit Analysis; Environmental Pollution; Hazardous Waste; Hydrocarbons; Indicators and Reagents; Organic Chemicals; Particle Size; Quaternary Ammonium Compounds