boron and silver-chloride

This paper presents a graphene nanosensor for affinity-based detection of low-charge, low-molecular-weight molecules, using glucose as a representative. The sensor is capable of measuring glucose concentration in a practically relevant range of 2 μM to 25 mM, and can potentially be used in noninvasive glucose monitoring.

Topics: Biosensing Techniques; Boron; Boronic Acids; Electrodes; Equipment Design; Esters; Glucose; Graphite; Humans; Hydrogen-Ion Concentration; Molecular Weight; Nanoparticles; Nanotechnology; Pyrenes; Silver; Silver Compounds

Electrochemical detection of sugar-related compounds was conducted using a boron-doped diamond (BDD) electrode as a detector for flow-injection analysis (FIA). Sugar-related compounds oxidize at high applied potentials, for which the BDD electrode is suitable for electrochemical measurements. Conditions for an FIA system with a BDD detector were optimized, and the following detection limits were achieved for sugar-related compounds: monosaccharides, 25-100 pmol; sugar alcohols, 10 pmol; and oligosaccharides, 10 pmol. The detection limit for monosaccharide D-glucose (Glu) was 105 pmol (S/N = 3). A linear range was acquired from the detection limit to 50 nmol, and the relative standard deviation was 0.65% (20 nmol, n = 6). A high-performance liquid chromatography (HPLC) column was added to the system between the sample injector and the detector and detection limits to the picomole level were achieved, which is the same for the HPLC system and the FIA system. The electrochemical oxidation reaction of Glu was examined using cyclic voltammetry with the BDD detector. The reaction proved to be irreversible, and proceeded according to the following two-step mechanism: (1) application of a high potential (2.00 V vs. Ag/AgCl) to the electrode causes water to electrolyze on the electrode surface with the simultaneous generation of a hydroxyl radical on the surface, and (2) the hydroxyl radical indirectly oxidizes Glu. Thus, Glu can be detected by an increase in the oxidation current caused by reactions with hydroxy radicals.

Topics: Alcohols; Boron; Buffers; Carbohydrates; Chromatography, High Pressure Liquid; Diamond; Electrochemistry; Electrodes; Flow Injection Analysis; Limit of Detection; Oxidation-Reduction; Silver; Silver Compounds

Coated capillary electrophoresis equipped with a boron doped diamond (BDD) electrode was developed for analysis of chemically synthesised 2-heptyl-3-hydroxy-4-quinolone (HHQ), 2-heptyl-3-hydroxy-4-quinolone (PQS), and 2-methyl analogues. Detection was then extended to biological samples. PQS and its biological precursor, HHQ, are two key regulators of bacterial cooperative behaviour known as quorum sensing in the nosocomial pathogen Pseudomonas aeruginosa. The fused silica capillary was coated with a thin layer of poly (diallyldimethylammonium) chloride to reverse the electroosmosis, allowing fast migration of PQS and HHQ with improved selectivity. The four model compounds were baseline resolved using a 50 mM H(3)PO(4)-Tris, pH 2.0 buffer with 20% (v/v) acetonitrile as buffer additive. With an injection time of 3 s, the detection limits of four analytes ranging from 60 to 100 nM (S/N=3) were observed when the BDD electrode was poised at +1.5 V vs. 3 M Ag/AgCl. As expected, no PQS or HHQ was detected from the supernatant of the P. aeruginosa (pqsA) mutant. A concentration of HHQ of 247 μM was detected from the supernatant of the pqsH mutant, which catalyses the conversion of HHQ to PQS in the presence of molecular oxygen by monooxygenase. The separation and detection scheme was applicable to follow the conversion of HHQ to PQS in P. aeruginosa when entering the stationary phase of growth. The results obtained by coated capillary electrophoresis with BDD detection were validated and compared well with LC-MS data.

Topics: Biomarkers; Boron; Burns; Diamond; Electrodes; Electrophoresis, Capillary; Humans; Limit of Detection; Polyethylenes; Pseudomonas aeruginosa; Pseudomonas Infections; Quaternary Ammonium Compounds; Quinolones; Quorum Sensing; Reproducibility of Results; Silver Compounds

A questionnaire was completed by fourteen world leading national metrology institutes to study the influence of several variables in the preparation of Ag/AgCl electrodes on the accuracy of Harned cell measurements of pH. The performance of each institute in the last decade has been assessed based on their results in eight key comparisons, organized by the Bureau International des Poids et Measures Consultative Committee for Amount of Substance, involving the measurement of pH of phosphate, phthalate, carbonate, borate and tetroxalate buffer solutions. The performance of each laboratory has been correlated to the results of the questionnaire to determine the critical parameters in the preparation of Ag/AgCl electrodes and their sensitivities with respect to the accuracy of pH measurement. This study reveals that the parameters most closely correlated to performance in comparisons are area of electrode wire exposed to the electrolyte, diameter and porosity of the Ag sphere prior to anodisation, amount of Ag converted to AgCl during anodisation, stability times employed for electrodes to reach equilibrium in solution prior to measurement, electrode rejection criteria employed and purity of reagents.

Topics: Boron; Buffers; Carbon; Chemistry, Physical; Electrochemistry; Electrodes; Hydrogen-Ion Concentration; Microscopy, Electron, Scanning; Reproducibility of Results; Silver; Silver Compounds; Surveys and Questionnaires